1、 接头的方法： 橡胶输送带接头的方法有：机械接头、冷粘接头、热硫化接头等几个常用的方法。 机械接头一般是指使用皮带扣接头，这种接头方法方便便捷，也比较经济，但是接头的效率低，容易损坏，对橡胶输送带产品的使用寿命有一定影响。 PVC和PVG整芯阻燃抗静电橡胶输送带接头中，一般8级带以下的产品都采用这种接头方法。
1. Joint method: Rubber conveyor belt joint method: mechanical joint, cold bonded joint, hot vulcanized joint and other commonly used methods. Mechanical joint generally refers to the use of belt buckle joint, which is convenient and economical, but the efficiency of the joint is low and easy to damage, which has a certain impact on the service life of rubber conveyor belt products. In the joints of PVC and PVG integral core flame retardant and antistatic rubber conveyor belts, the joint method is generally used for products below grade 8 belt.
2、冷粘接头：即采用冷粘粘合剂来进行接头。这种接头办法比机械接头的效率高，也比较经济，应该能够有比较好的接头效果，但是从实践来看，由于工艺条件比较难掌握，另外粘合剂的质量对接头的影响非常大，所以不是很稳定。 热硫化接头，实践证明是理想的一种接头方法，能够保证高的接头效率，同时也非常稳定，接头寿命也很长，容易掌握。但是存在工艺麻烦、费用高、接头时间长等缺点。
2. Cold bonded joints: that is to say, cold bonded adhesives are used for joints. This kind of joint method is more efficient and economical than mechanical joint. It should have better joint effect. However, in practice, it is not very stable because the process conditions are difficult to master and the quality of adhesives has a great influence on the joint. Thermal vulcanized joints have been proved to be the most ideal joint method, which can ensure high joint efficiency, stability, long service life and easy to grasp. However, there are some shortcomings, such as troublesome process, high cost and long joint time.
3、分层橡胶输送带的接头： 可以根据需要采用机械接头、冷粘接头、热硫化接头等接头方法。一般冷粘接头、热硫化接头采取的是阶梯式结构接头。
3. Joints of layered rubber conveyor belts: mechanical joints, cold-bonded joints and hot-vulcanized joints can be used as required. Generally, the cold bonded and hot vulcanized joints adopt the stepped structure joints.
4、PVC和PVG整芯阻燃橡胶输送带的接头： 由于整芯带的结构比较特殊，接头不太容易，所以大多数采用机械接头办法，即皮带扣接头。但是8级以上的橡胶输送带，为了保证接头效果，一般还是采用热硫化接头的方法。接头的结构都是指状接头。PVC和PVG整芯阻燃橡胶输送带的热硫化接头工艺比较复杂，对设备的要求也比较高。
4. Joints of PVC and PVG Whole-core flame-retardant rubber conveyor belts: Because the structure of the Whole-core belt is special and the joints are not easy, most of them adopt mechanical joints, i.e. belt buckle joints. However, for rubber conveyor belts above grade 8, in order to ensure the effect of joints, hot vulcanized joints are generally used. The joints are all finger joints. The process of hot vulcanization joint of PVC and PVG whole core flame retardant rubber conveyor belt is complex, and the requirement for equipment is relatively high.
